Results 1 to 9 of 9
Like Tree7Likes
  • 5 Post By romaniac
  • 1 Post By romaniac
  • 1 Post By <---cop

Thread: trading...

  1. #1
    Senior Member
    Join Date
    Feb 2013
    Location
    Asia
    Posts
    431

    trading...

    should i trade the ZAU for a cobra?
    i didnt like the ZAU cause of the 1.5mm air hole.
    someone offered me a trade for a 5ml cobra with 1.3mm wick hole. will that make a big difference?
    anyone has used both can tell me the main differences?
    thanks

    note: i like the aga-t2 with a 1mm hole
    Last edited by yuujin; 26-03-13 at 05:59 AM.


    Tops : AC9 / Cobra / Kayfun Lite / Killer 705 / SS Steam Turbine
    Bottoms : Atmizoo Roller SS-IM / Super T Precise ELA
    Lists : Senesis

  2. #2
    AV Approved Manafacturer/Modder
    Join Date
    May 2011
    Location
    Las Vegas
    Posts
    463
    Buy some aluminum tape. use a paper hole puncher and punch some holes of the aluminum tape . Place the little round tape circle over the air hole and press firmly. Using a needle poke a little hole enlarge until is the right draw for you.


    WWW.JAZZEPIPE.COM

  3. #3
    Senior Member
    Join Date
    Feb 2013
    Location
    Asia
    Posts
    431
    would it be possible to do this on the inside of the cap?


    Tops : AC9 / Cobra / Kayfun Lite / Killer 705 / SS Steam Turbine
    Bottoms : Atmizoo Roller SS-IM / Super T Precise ELA
    Lists : Senesis

  4. #4
    AV Approved Manafacturer/Modder
    Join Date
    May 2011
    Location
    Las Vegas
    Posts
    463
    Quote Originally Posted by yuujin View Post
    would it be possible to do this on the inside of the cap?
    yes of course but you have to clean the cap dry . if is any residue it will not stick.

    WWW.JAZZEPIPE.COM

  5. #5
    Senior Member
    Join Date
    Feb 2013
    Location
    Asia
    Posts
    431
    Quote Originally Posted by romaniac View Post
    yes of course but you have to clean the cap dry . if is any residue it will not stick.
    after sticking, when vaping will it drop?
    sorry romaniac, i do not have experience with aluminum tape.


    Tops : AC9 / Cobra / Kayfun Lite / Killer 705 / SS Steam Turbine
    Bottoms : Atmizoo Roller SS-IM / Super T Precise ELA
    Lists : Senesis

  6. #6
    AV Approved Manafacturer/Modder
    Join Date
    May 2011
    Location
    Las Vegas
    Posts
    463
    I am not sure I never try it. But most likely it will. Also is hard to punch the hole without pushing the sticker . Trust me if you place the aluminum tape circle directly over the hole and you press it well before punching it will look very acceptable . I have done that on a AC9 and it took few tries before I got it right. But will do the job very well and if you place the circle right it will look good also
    davee likes this.

    WWW.JAZZEPIPE.COM

  7. #7
    Senior Member
    Join Date
    Feb 2013
    Location
    Asia
    Posts
    431
    Quote Originally Posted by romaniac View Post
    I am not sure I never try it. But most likely it will. Also is hard to punch the hole without pushing the sticker . Trust me if you place the aluminum tape circle directly over the hole and you press it well before punching it will look very acceptable . I have done that on a AC9 and it took few tries before I got it right. But will do the job very well and if you place the circle right it will look good also
    i see! thanks romaniac. will try.


    Tops : AC9 / Cobra / Kayfun Lite / Killer 705 / SS Steam Turbine
    Bottoms : Atmizoo Roller SS-IM / Super T Precise ELA
    Lists : Senesis

  8. #8
    Senior Member
    Join Date
    Nov 2011
    Location
    Australia
    Posts
    4,055
    The other thing you can do is use jb weld to fill up the hole from the inside and redrill it smaller.
    The top cap will look completely stock.
    You could always buy another replacement top cap to work on. In stock at electronicstix.
    ElectronicStix.Com Zenesis/Z-Atty Open Draw Top Cap

    I wouldn't swap a ZAU for an enormous 5ml cobra.
    romaniac likes this.

  9. #9
    Senior Member
    Join Date
    Nov 2012
    Location
    Brisbane
    Posts
    2,877
    I have cobra clone if you want to trade :-P

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin® Version 4.2.4
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO 3.6.0
All times are GMT +11. The time now is 03:22 PM.