Results 1 to 5 of 5
  1. #1
    AVF Newbie | Be nice to me
    Join Date
    Feb 2015
    Location
    Sydney
    Posts
    48

    Silo beast and Itaste MVP 2.0

    Hi all,

    Having a bit of an issue. Just bought a silo beast to go on my Itaste 2.0 box, however it isn't working. I put the beast on ego one and it works without problem. I also tried an ego one Clearo on the Itaste to make sure it's working and it works without issue.

    Is there any reason why the silo beast isn't burning while on an Itaste 2.0?

    Thanks.

  2. #2
    AVF Regular
    Join Date
    Aug 2014
    Location
    Sydney (or lurking in the shadows behind you)
    Posts
    2,298
    Quote Originally Posted by ElusiveEnd View Post
    Hi all,

    Having a bit of an issue. Just bought a silo beast to go on my Itaste 2.0 box, however it isn't working. I put the beast on ego one and it works without problem. I also tried an ego one Clearo on the Itaste to make sure it's working and it works without issue.

    Is there any reason why the silo beast isn't burning while on an Itaste 2.0?

    Thanks.
    Hmm ...
    Silo Beast Sub Ohm Tank is it?
    What resistance is the coil in that?

    The Innokin iTaste MVP 2.0 has an amp limit of 2.5 amps,
    it just can't Sub Ohm.

    I Do Whatever I Want,
    Whenever I Want,
    And If It Doesn't Suit You,
    Go Start Your Own Empire

    Anything I write on this Forum is purely my opinion and should never be read as fact!
    (or I could just be wrong)
    Please read the Forum rules
    (or wait for Johnny Depp to do the movie)
    Small reminder
    It's all about the cigartte ... Stupid



  3. #3
    AVF Newbie | Be nice to me
    Join Date
    Feb 2015
    Location
    Sydney
    Posts
    48
    It has the default coil in it, think it's 0.5.
    The guy at the shop said it would be fine when I mentioned it was for an MVP 2.0

  4. #4
    AVF Regular
    Join Date
    Jan 2014
    Location
    Perth WA
    Posts
    1,207
    Specs
    As an upgrade of the original iTaste MVP , the iTaste MVP 2.0 has substantial improvements in both appearance and function.
    Variable Voltage: voltage can be adjusted from 3.3 5.0 volts in .1 volt increments.
    VariableWattage: Wattage can be adjusted from 6.0 11.0 W in .5 watts increments.
    Ohmsmeter: Reads resistance of your atomizer/cartomizer/clearomizer.
    Battery Level Indicator:
    The iTaste MVP2.0 e cigarette battery capacity is displayed via green, yellow and red LED lights.
    Green = Fully Charged
    When the iTaste MVP2.0 is fully charged the LED light will turn green and power off.
    Yellow = Half Discharged
    Red = In need of charging
    Puff Counter
    Short Circuit/Atomizer Protection.
    Over-Discharge Protection.
    Battery Level Indicator
    Large battery capacity: iTaste MVP e cigarette built-in 2600 mAh polymer Li-Ion rechargeable battery.
    High compatibility 510 connector: Thread fit iClear10,iClear16 ,iClear30 etc.
    ON/OFF battery switch: 10 seconds cutoff.
    Passthrough / Vape While Charging Technology.
    Remembers last set voltage or wattage: Remembers last set voltage or wattage when the battery is turned off and then back on.
    Built-in 3 digit display: Digital display shows Ohms meter, Voltage /Wattage setting, number of puffs taken since last time the battery was turned off.
    Portable power source for electronic products.
    From what I can see they dont give a minimum resistance ( not good) but I would think your 0.5 ohm coil is to low.
    You should not be guessing what resistance your coil is you should know before you use it on a device. Its all about safety

  5. #5
    AVF Regular
    Join Date
    Aug 2014
    Location
    Sydney (or lurking in the shadows behind you)
    Posts
    2,298
    Quote Originally Posted by ElusiveEnd View Post
    It has the default coil in it, think it's 0.5.
    The guy at the shop said it would be fine when I mentioned it was for an MVP 2.0
    On a MPV 3 & MPV 3 Pro it would work,
    perhaps he miss heard you?

    Does the 1.8Ohm Aspire TRITON Replacement coil option fit?
    If the Silo came with a 1.2 ohm coil that will work
    Last edited by Snidely_Whiplash; 10-01-16 at 02:54 PM.

    I Do Whatever I Want,
    Whenever I Want,
    And If It Doesn't Suit You,
    Go Start Your Own Empire

    Anything I write on this Forum is purely my opinion and should never be read as fact!
    (or I could just be wrong)
    Please read the Forum rules
    (or wait for Johnny Depp to do the movie)
    Small reminder
    It's all about the cigartte ... Stupid



 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin® Version 4.2.4
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO 3.6.0
All times are GMT +11. The time now is 06:55 PM.