Page 1 of 3 123 LastLast
Results 1 to 10 of 24
Like Tree14Likes

Thread: orion v3

  1. #1
    AVF Regular
    Join Date
    Feb 2011
    Location
    gympie queensland
    Posts
    2,350

    orion v3

    this looks good,as long as it dont leak.more info at vp.
    ckane, RIDING OLD SKOOL and bugzme like this.
    RIP VP

  2. #2
    AVF Regular
    Join Date
    Jun 2011
    Location
    Melbs
    Posts
    4,963
    Looks like he has ripped the guts out of a Provari
    Move along!!! Nothing to see here.

  3. #3
    AVF Regular
    Join Date
    Feb 2011
    Location
    gympie queensland
    Posts
    2,350
    stole this from stickyfingers.looks a lot like another mods guts.
    New v3 will be equipped with such controls

    Technical specifications:

    1: Variable watt 5-15W
    2: 15 Second Cutoff
    3: Short Circuit Protection
    4: Reverse Battery Protection
    5: Discharge Protection (adjustable 2.9-7V)
    6: Temperature Monitoring
    7: Overload Protection
    8: On - Off Mode
    9: 10 minutes auto-off
    10: Stacked Batteries 2 x 18350 or 1x 18650
    11: Resistance check
    12: Battery Volt check
    13: Check battery volts under load

    Programs:

    P1: Power up
    P2: Power down
    P3: Measurement of resistance atomizer (Ohm)
    P4: Measurement of the battery and the battery under load (Volts)
    P5: Discharge Protection (adjustable 2.9-7V)
    P6: On-off
    E: Error Codes and delete

    Error codes:

    0: Other error
    1: Resistance interrupted
    2: Resistance to large
    3: Resistance to small
    4: Short circuit or wobble contact
    5: Battery voltage too low
    6: Overheating
    7: Max power time exceeded
    bugzme likes this.
    RIP VP

  4. #4
    AVF Regular
    Join Date
    Jul 2011
    Location
    Melb
    Posts
    5,139
    I hope its not too much bigger than the 2.1. That's the best thing about the orion, its size.

  5. #5
    AVF Regular
    Join Date
    Feb 2011
    Location
    gympie queensland
    Posts
    2,350
    prolly 25-30 mm longer would be my guess.
    RIP VP

  6. #6
    Senior Member
    Join Date
    May 2012
    Location
    Tweed Heads........ # i vape 18mg#
    Posts
    2,088
    looks the goods !
    Living is easy with eyes closed, misunderstanding all you see.....im off to the PUB

  7. #7
    AVF Regular
    Join Date
    Jul 2011
    Location
    Melb
    Posts
    5,139
    I think I'll stick with the 2.1

  8. #8
    AVF Regular
    Join Date
    Jun 2011
    Location
    Melbs
    Posts
    4,963
    I thought Les was going all out with a Patent? Must of succumbed to the Chinese electronics.
    Move along!!! Nothing to see here.

  9. #9
    AVF Regular
    Join Date
    Jul 2011
    Location
    Melb
    Posts
    5,139
    I think it would have been better if he stuck with palipoe. Dont like the screen either. Im sure its still in early stages. then there will be the 3.1

  10. #10
    AVF Regular
    Join Date
    Dec 2012
    Location
    Melbourne Vic
    Posts
    3,151
    to be honest, im not very happy about this design. a hybrid should stay a hybrid. its pure that way, if i wanted VV/VW id go with my vamo. i dont realy think theres a point to have a hybrid with VV/VW if the atomizer has only one wick hole. theres only so many variations you can try on it and eventually itll all be the same regardless what Volts and Watts you set it at. the novelty of having that kind of electrical module would pass quick. id have liekd it if all he did was the airholes and made it a mechanical switch. that was the only thing stopping me from getting the 2.1.
    studiovape likes this.

 

 
Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin® Version 4.2.4
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO 3.6.0
All times are GMT +11. The time now is 11:25 AM.